Daily Archives: March 31, 2016

2016 Fly Swap – Troutchaser’s Tequeely Streamer

TequeelyStreamer-Troutchaser

Submitted by message board member, Troutchaser – who is the author of a new book, Fly-Fishing for Trout in Southeast Minnesota which can be found at www.troutchasers.net

Tequeelly Streamer . . . for big trout (or smallmouth)

Hook: 3XL streamer, sizes 2 down to 8

Bead: Copper or Gold Cone or Bead
(or you can use dumbbell eyes to ride hook-point up)

Thread: 6/0 black, tan or orange

Tail: Yellow Marabou and Black Marabou

Body: Copper Crystal Chenille or Root Beer Cactus Chenille

Legs: Medium round yellow rubber

1: Tying is pretty straight-forward. De-barb hook and slide on a cone or bead.

2: Wrap a thread base from the cone to the bend and back and then return to the
bend to tie in a clump of yellow marabou. Bind down marabou stem and fluff to the
back of the cone. Tail should be shank-length.

3: Repeat with a black clump of marabou, and then on top of the black, add a clump
of yellow marabou. Binding down along the shank gives the body some bulk.

4: Tie in the Crystal Chenille behind the cone and bind it down to the bend on top of
the hook. Take the thread back to a 1/3rd point (above the hook point).

5: Wrap the Crystal Chenille to this 1/3rd point and clip a heavy hackle pliers to it so
it stays put.

6: Take two 2” lengths of rubber, bend around thread, and tie on together loosely,
slide one to the rear side, and tighten down with two tight wraps. Advance thread
to the 2/3rd point, and then wrap the Crystal Chenille to this point, passing it
between the “X” of the rubber legs as you do so.

7: Repeat the process for a second set of legs, move the thread to just behind the
cone, and repeat the process for a third set of legs. Whip-finish twice and clip the
thread. Tweak the legs so they are horizontal and shorten the leg length if necessary.
8: Run this fly through deep holes, especially rip-rapped banks near roads, downed
trees, and other big-trout hide-outs. Dusk and dawn are always good.

Notes for tying: Tequila was involved in the creation of this streamer.
If you are using a cone, tuck a few wraps of lead inside the cone to stabilize it.
Chartreuse marabou is a good option to the yellow marabou
Reminder: Trout turn piscivorous once they are 5” long.

2016 Fly Swap – TFO5wt’s Foam Hopper

FoamHopperTFO5wt

Submitted by message board member TFO5wt. Here are his notes:

Foam Hopper

Hook: TMC 2312 size 6
Thread: Olive Uni 8/0 (smaller thread creates better abdomen segments and it’s all superglued in the end)
Body: 2 mm thin foam (green in this case) and 2 mm thin foam (yellow) for indicator. Cut two green strips approximately width of hook gap and 1 1/4 the length of hook for under and over body. Cut a chunk of yellow the same width and 1/2 the hook length.
Legs: Back are small green foam strips (slivers really) and front are barred olive rubber legs
Wing: yellow Puglisi EP fibers (craft fur, Antron, poly, etc)

Pictures of materials, various steps, and finished views: http://imgur.com/a/Qhrg3

1. Wrap thread to bend of hook
2. Cut the last 1/4 of green foam strips in a triangle for tail. Tie both on hook bend just after end of triangle.
3. Lift up strips and wrap thread 3-4 wraps forward, then wrap secure underbody foam strip, repeat twice to form segmented abdomen with three sections. Stop just a bit forward of the half way point on hook.
4. Tie in each foam leg slivers on top of tied down underbody abdomen foam strip for back legs(these will be sandwiched between two body segments)
5. Tie in second foam strip (overbody) over foam legs
6.Tie in wing material on top of underbody/leg/overbody sandwich
7. Tie in yellow foam piece for indicator on top of wing/leg/body sandwich
8. Lift foam and wrap forward to create thorax section (roughly 2/3 the size of abdomen)
9. Tie down underbdy foam strip
10. Tie in rubber legs
11. Tie down overbody and indicator foam strips to create another foam sandwich
12. Lift remaining unsecured foam (head), wrap to the hook eye, and whip finish
13. Use a dab of superglue gel to stick three foam strips in head together. Cut to foam strips to make even head.
14. Use another dab of superglue to stick tail sections together.
15. Use a small bead of superglue on the underside to secure thread to hook.

Some notes on the bug: Overall body size can be changed (longer, fatter, slimmer, etc) without changing hook size. I also tie this in two-tone yellow underbody and green overbody, and tan. All work. Back legs create a great profile and stability. It always lands and rides correctly. When tying don’t worry about top of bug not staying completely centered on hook, just make sure underbody is not twisting and staying centered. Fish see the bottom not the top. It floats like a cork, just grease the wing from time to time. Hang on cause it gets hammered.